Thank you for writing to us. One of our executive will reach back to you through your submitted medium. In case there’s an urgency, feel free to connect over WhatsApp for faster response.
Nitta PolyBelt flat power transmission and conveying belts pair a high-tensile polyamide (PA) core with abrasion-resistant NBR synthetic rubber covers, supporting speeds up to 70 m/s and antistatic properties (≤ 500 V). Details are available in the Nitta PolyBelt Catalog and on the Nitta PolyBelt Page.
General Construction & Performance
• Tension Member: High-tensile polyamide (PA / nylon) film or fabric core built for shock loads and low elongation.
• Cover Material: Abrasion- and oil-resistant NBR (nitrile butadiene rubber) or soft NBR on top/bottom surfaces.
• Operating Speed: Up to 50–70 m/s depending on belt series and drive setup.
• Operating Temperature: Typically -20°C to +80°C.
• Antistatic Rating: ≤ 500 V to prevent static charge build-up.
• Joining: Skived endless joining on-site or factory-made endless loops.
Sample Model Specifications
• M-2000: 4.0 mm thickness, 30.0 N/mm specific tension at 2% elongation, 200 mm minimum pulley diameter (fans, pumps, spinning frames, cardboard/paper machinery).
• H-500: 3.5 mm thickness, 7.5 N/mm specific tension at 2% elongation, 50 mm minimum pulley diameter (tangential drives, generators/blowers, conveyors).
• H-750: 3.75 mm thickness, 11.2 N/mm specific tension at 2% elongation, 75 mm minimum pulley diameter.
• H-1500: 4.5 mm thickness, 22.5 N/mm specific tension at 2% elongation, 150 mm minimum pulley diameter.
• TFL-6S to TFL-18S: 2.25 mm to 3.35 mm thickness, 11.5 to 34.0 N/mm specific tension at 2% elongation, 60 mm to 175 mm minimum pulley diameter (low-noise tangential drives and roller conveyors).
• XH-3S-3 / XH-3S-4 / XH-3S-6: 2.85–3.0 mm, 3.85–4.0 mm, and 5.85–6.0 mm thicknesses, 3.4 N/mm tension at 1% elongation, 50 mm, 60 mm, and 80 mm minimum pulley diameters (folder gluers and paper/cardboard handling).
Restrictions & Series Coverage
• Product Series: Includes SG, L, M, H, MH, TFL, XH, CBX-7S, CBE-20, CBG-7S, NRT, RT, IRTA, KCS, and TTA/TTB/GLTB/GMTB/TW/TWH variants.
• Safety Prohibitions: Not approved for hoisting loads, conveying unpackaged food, or incineration.
If you share:
• The exact belt series or model code (for example, M-2000, H-1500, or XH-3S)
• Your required width, thickness, or pulley diameter
• The application or machinery type
I can verify the exact rating, tension, and compatibility details for your setup.
Plain (flat) belts with a top sponge coating combine a smooth, non-toothed base belt with a compressible sponge rubber or foam layer to cushion, grip, and convey delicate items without marring.
Typical Specifications
• Base Belt Material: Flat rubber, rubber-nylon, PVC, polyurethane (PU), or fabric belts (typically starting from ~0.8 mm thick).
• Top Sponge / Foam Coating: Sponge rubber, PU sponge/foam, or closed-cell foam (including FDA-grade white sponge for food/packaging).
• Coating Thickness: Commonly 1 mm to 20 mm depending on application and supplier (standard stock options often include 3 mm, 4 mm, 6 mm, 8 mm, 10 mm, or 15 mm).
• Hardness: Typically 30°–50° Shore A (with some rubber/sponge ranges extending up to 60° Shore A).
• Surface & Finish Options: Bare sponge, top-cloth/fabric skin (such as woven cloth, lycra, or silicone-treated covers for higher wear and tear resistance), or cross-cuts/grooves for conformity.
• Dimensions: Custom widths and lengths/endless loops to match conveyor or feeder frames.
Polyurethane (PU) timing belts with a top silicone coating combine the precise power transmission and wear resistance of a toothed PU belt with higher surface grip, lower noise, and better heat or chemical resistance on the back side.
Key Specifications
• Base Belt Material: Thermoplastic polyurethane (PU), typically around 70–90 Shore A hardness, with steel, Kevlar/aramid, or fiberglass tension cords.
• Common Tooth Profiles: Metric profiles (such as T2.5, T5, T10, T20, AT5, AT10, AT20), imperial profiles (XL, L, H, XH), and curvilinear profiles (such as HTD).
• Silicone Coating Thickness: Typically ranges from 0.5 mm to 12 mm depending on the manufacturer and conveyor/grip requirement (commonly 1.5 mm to 10 mm on standard custom belts).
• Coating Hardness: Often softer than the PU base (for example, around 35–40 Shore A) to increase surface friction, cushioning, and anti-slip grip.
• Temperature Resistance: Uncoated standard PU belts generally operate around -30°C to +80°C, whereas specialized silicone formulations can extend high-temperature tolerance up to 100°C–250°C depending on the exact compound and construction.
Megadyne polyurethane (PU) timing belts—including the MEGAPOWER, MEGAFLEX, and MEGALINEAR series—are synchronous power transmission and linear motion belts available in thermoset (88 ShA) or thermoplastic (92 ShA) polyurethane reinforced with steel or Kevlar cords.
Key Specifications by Series
• MEGAPOWER / MEGAPOWER 2 (Endless Molded PU): Grey/green thermoset polyurethane (88 ShA) with standard zinc-coated steel or optional Kevlar, fiberglass, or stainless steel cords. Operates from -25°C to +80°C at speeds up to 20 m/s. Common profiles include T2, T2.5, MXL, XL, L, and H (with T/AT aligning with ISO 17396).
• MEGAFLEX (Truly Endless PU): White thermoplastic polyurethane (92 ShA) with continuous spiral steel or optional Kevlar/stainless steel cords. Supports speeds up to 10,000 RPM and 20 m/s across temperatures from -25°C to +80°C. Features a wide range of profiles including XL, L, H, T-series, AT-series, and RPP variants.
• MEGALINEAR (Open-End & Jointed PU): White thermoplastic polyurethane (92 ShA) reinforced with parallel steel, Kevlar, or stainless steel cords. Built for high linear motion drives with speeds up to 70 m/s and temperatures from -30°C to +80°C. Available in extensive metric, imperial, and specialized profiles.
General Construction & Options
• Performance & Resistance: High resistance to abrasion, low elongation, and strong tolerance to oils, greases, ozone, and hydrolysis.
• Add-ons: Optional nylon tooth or back facings and custom backing thicknesses for specific conveying applications.
For detailed engineering catalogs and dimensions, consult official resources such as the Megadyne MEGALINEAR page, the Megadyne MEGALINEAR Brochure, the Megadyne Product Guide, or regional distributors like Pratham International.
Please share the tooth profile and pitch (such as T5, AT10, or RPP8), belt length or tooth count, belt width, and cord material (steel or Kevlar) so I can provide exact dimensions or part details.
•
Megadyne
product-detail-entry-exit
ANJANEYA BELTINGS, A.K.RAO Nilayam, NO: 9/406A, Sakthi Nagar, Ist street, Tirusulam, CHENNAI – 600 043 - Tamil Nadu – ., CONTACT DETAILS: 93810 23876 - 98400 43808 - 97031 98344